INSTALLATION INSTRUCTION
For Wall Mount Light Fixtures (Rev. 07/09/2005)
Fig. A
Fig. B
PREPARATION
1. Shut off power at the fuse box or circuit breaker box. If
necessary, remove old fixture and all mounting hardware from
wall junction box.
2. Carefully unpack your new fixture and lay out all the parts on a
clear area. Take care not to lose any small parts necessary for
installation.
MOUNTING THE FIXTURE
3. Your new fixture will be either a Circular Strap (Fig. A) mounting,
or a Crossbar (Fig. B) mounting type.
Determine which type your fixture is by the parts shipped with
your fixture and follow the appropriate instruction. NOTE: The
wiring is the same for either fixture.
Fig. A CIRCULAR STRAP MOUNTING
A1. Find the pair of holes with Indentations in the Circular Strap (A).
Thread Screw Studs (H) from the indented side into the Circular
Strap (A) and out to the raised side. Thread Nuts (C) onto Screw
Studs (H) and tightly secure as illustrated in Fig A.
A2. Place the Circular Strap (A) over the junction box so the Screw
Studs (H) is vertical or horizontal as required by fixture type.
Secure to the junction box by threading the two junction box
screws (B) through the slotted holes. The side of the Circular
Strap marked “GND” must face out.
A3. Connect the wires as described under “Connecting the Wires”.
A4. Place the fixture Canopy (D) over the two Screw Studs (H) so
they protrude through the holes in the Canopy (D). Thread the
Cap Nuts (E) onto the Screw Studs (H) and continue turning until
the Fixture is snug against the wall. (See “Completing the
Installation”)
Fig. B CROSSBAR MOUNTING
B1. Attach the Crossbar (A) to the junction box with the two Junction
box screws (B) as shown. The side of the Crossbar marked
“GND” must face out.
B2. Thread the Nipple (C) part way into the center hole of the
Crossbar.
B3. Connect the wires as described under “Connecting the Wires”.
B4. Place the fixture Canopy (D) over the Nipple so the Nipple
protrudes through the center hole. Holding the fixture in place,
thread the Cap Nut (E) onto the end of the Nipple until fixture is
secure to the wall. (See “Completing the Installation”).
CONNECTING THE WIRES
Connect the fixture wires to the junction box wires as shown in the wiring
diagram. Making sure all wire connectors are secured and do not easily
pull off with a slight tug. If there is no Green Ground wire from the
junction box, connect the Fixture Ground Wire to the Circular Strap or
the Crossbar with the green Screw provided.
COMPLETING THE INSTALLATION
4. Loosen screws in the holder (G) then insert glass shade (F) into
holder (G). Secure shade assembly by adjusting each screw in
holder (G).
5. Install the proper light bulbs for your fixture. DO NOT EXCEED
THE SPECIFIED WATTAGE! Return the power to the junction box
and test the fixture.
Your installation is now complete.
LA-801E/F
FIXTURE
WIRES
Black or
Smooth
H
USE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
USE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
USE
WIRES
Green
(Ground)
Note: Illustration (Fig. A and B) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased
.
G
F
C
E
D
B
A
JUNCTION BOX
H
JUNCTION BOX
A
B
G
F
D
E
C
In the event that you should have any installation
question or are missing parts, please contact
Customer Service. Customer service may be reached
weekdays a 1-800-527-0998 between the hours of
8:00am and 5:00pm PST (Pacific Standard Time).
(2 pages)
(24 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals