INSTALLATION INSTRUCTIONS
New 07/12/2004
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
Fig. 1
Fig. 2
Fig. 3
ASSEMBLING THE FIXTURE (Fig.1)
1. Carefully remove the fixture from the carton and check that all parts
are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old fixture including
the crossbar.
3. Secure the Loop (A) to the Top Housing (B).
4. Rotate top Tire Arm (H) to proper position as shown in Fig 1.
5. Connect top end of Drop Rod (J) to Joint (C) on Top Housing (B)
using Screw (E) and Cap (D), do the same with the other Drop Rods.
6. Connect bottom end of Drop Rod (J) to Joint (M) on Metal Ring using
Stud (K) and Nut (L), do the same with the other Drop Rods.
7. Place Glass Shade (I) over the Socket and secure in place with
Tube (G) provided and Screw Shell (F).
8. Install the light bulbs in accordance with the fixture’s specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
HANGING THE FIXTURE (Fig. 2)
9. Thread Nipple into Loop until snug.
10. Thread other end of Nipple with Loop attached into crossbar until
snug.
11. Place Lock Washer over end of Nipple protruding through crossbar
and thread Hex Nut onto nipple until tight.
12. Take the crossbar assembly and mount to ceiling junction box with
junction box screws. Tighten screws securely with screwdriver.
13. By measuring determine correct number of links needed for proper
hanging height.
14. Use a pair of pliers to open one end link of the chain, attach the
chain to the fixture’s loop, close the link. Slip Lock Collar followed by
the Canopy over the chain. Open the other end link of the chain and
lift the fixture to attach to the ceiling loop, close the chain link.
15. Lace the fixture’s wires through the chain links and pull until taut.
Feed the fixture wires through the loop and Nipple and pull until taut.
CONNECTING THE WIRES (Fig. 3)
16. At this point, connect the electrical wire as shown in figure 3, making
sure that all wire connectors are secured. If your outlet has a ground
wire (green or bare copper), connect the fixtures Ground Wire to it.
Otherwise, connect the fixture Ground Wire directly to the crossbar
using the Green Screw provided.
17. Tuck these wire connections neatly into the ceiling junction box and
then raise the canopy all the way to the ceiling. Raise the Lock Collar
and thread onto ceiling Loop protruding through canopy.
Your installation is now complete. Return power to the junction box
and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
LA-834E/S
FIXTURE
WIRES
Black or
Smooth
H
USE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
USE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
USE
WIRES
Green
(Ground)
H
C
E
D
F
G
I
M
K
L
A
B
J
Nipple
Screw
Canopy
Loop
Chain
Hex Nut
Lock Washer
Crossbar
Loop
Lock Collar
Junction Box
(Ceiling)
In the event that you should have any installation question or are missing
parts, please contact Customer Service. Customer service may be reached
weekdays a 1-800-527-0998 between the hours of 8:00am and 5:00pm PST
(Pacific Standard Time).
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
(32 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals