INSTALLATION INSTRUCTIONS
For Model # 27011 (REV.10/06/2003)
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
Fig. 1
Fig. 2
Fig. 3
ASSEMBLING THE FIXTURE (Fig. 1)
1. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old fixture
including the crossbar.
3. Adjust the Arms (A) to proper position.
4. Place Shade (D) over the Glass Ring (E).
5. Bring the Glass Ring (E) and the Shade (D) as illustrated to
attach to Arm (A).
6. Secure the combination (E) (D) and (A) by pushing stud (B)
through the Glass Ring (E) and tighten with Decorative Nut
(C).
7. Repeat assembly on the other side.
8. Install Light bulbs in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING).
HANGING THE FIXTURE (Fig. 2)
9. Thread Nipple into Loop until snug.
10. Thread other end of Nipple with Loop attached into crossbar
until snug.
11. Place Lock Washer over end of Nipple protruding through
crossbar and thread Hex Nut onto nipple until tight.
12. Take the crossbar assembly and mount to ceiling junction box
with junction box screws. Tighten screws securely with
screwdriver.
13. By measuring determine correct number of links needed for
proper hanging height.
14. Use a pair of pliers to open one end link of the chain, attach
the chain to the fixture’s loop, and close the link. Slip Loop
Collar and Canopy over the chain.
15. Open the other end link of the chain and lift the fixture to
attach to the ceiling loop, close the chain link.
16. Lace the fixture’s wires through the chain links and pull until
taut. Feed the fixture wires through the Loop and Nipple and
pull until taut.
CONNECTING THE WIRES (Fig. 3)
17. At this point, connect the electrical wire as shown in figure 3,
making sure that all wire connectors are secured. If your
outlet has a ground wire (green or bare copper), connect the
fixtures Ground Wire to it. Otherwise, connect the fixture
Ground Wire directly to the crossbar using the Green Screw
provided.
18. Tuck these wire connections neatly into the ceiling junction
box and then raise the canopy all the way to the ceiling.
Raise the Lock Collar and thread onto ceiling Loop protruding
through canopy.
Your installation is now complete. Return power to the
junction box and test the fixture.
Nipple
Screw
Canopy
A
Chain
Hex Nut
Lock Washer
Crossbar
Loop
Lock Collar
Junction Box
(Ceiling)
-
A
B
C
D
E
In the event that you should have any installation question or are missing
parts, please contact Customer Service. Customer service may be reached
weekdays a 1-800-527-0998 between the hours of 8:00am and 5:00pm PST
(Pacific Standard Time).
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
FIXTURE
WIRES
Black or
Smooth
H
USE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
USE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
USE
WIRES
Green
(Ground)
(12 pages)
(10 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals